A 4ft LED wraparound light is the quickest way to retire the old two lamp fluorescent wraps in hallways, back rooms, storage closets and classrooms. The housing goes up on the same ceiling or junction box, there are no tubes or ballasts left to service, and most current models let you pick the wattage and color temperature on the fixture. The catch is that wraps that look the same in a photo can be very different on the spec sheet. Here is how to compare them, with the numbers taken straight from the manufacturer sheets.
What a wraparound light is, and where it fits
A wraparound is a surface mount linear fixture with a lens that curves over the top and both sides, so light spreads across the ceiling and walls instead of only straight down. That wide spread is why wraps were the standard fluorescent fixture for corridors, utility rooms, break rooms and other hard ceiling spaces where there is no grid for a troffer.
| Space | Why a wrap works | Look for |
|---|---|---|
| Hallways and corridors | Wide lens lights the walls as well as the floor | Sensor base, chain end to end runs |
| Back rooms and storage | Surface or J box mount on drywall or concrete | Occupancy sensor so lights do not run all night |
| Classrooms and offices | Low glare frosted lens over desks | 0 to 10V dimming, 3500K or 4000K |
| Restrooms and break rooms | Short runs on a hard ceiling | Damp location rating where the room needs it |
If the space has a drop ceiling, a panel or a troffer kit is usually the better fit. See troffer retrofit kits vs new fixtures. If you only want to swap lamps in a fixture you are keeping, see how to replace 4ft fluorescent tubes with LED.
4ft LED wraparound lights compared by spec sheet
Here are seven 4ft wraps from our wraparound collection, all with a posted price. Wattage, lumens and dimensions come from the manufacturer spec sheets; prices are from the product pages at the time of writing and can change.
| Fixture | Selectable wattage | Max lumens | CCT | Size (L x W x H) | Price |
|---|---|---|---|---|---|
| Gielight WR 4ft | 24 / 31 / 38 / 46W | See sheet | 3000K to 6500K, 5 settings | 46.98" x 5.37" x 2.36" | $30.00 |
| JEE J WRAP 4ft | 20 / 30 / 40W | 5,000 lm | 3500K to 6500K, 5 settings | 47" x 5.3" x 2.2" | $33.50 |
| TCP Select Series Modern Wrap SW4 | 32 / 40 / 48W | 5,520 lm | 3500K / 4000K / 5000K | 47.6" x 5.3" x 2.1" | $34.50 |
| TCP Select Series Wrap SW3 | 30 / 35 / 40W | 5,200 lm | 3500K / 4000K / 5000K | See sheet | $37.00 |
| EDIPAI Wraparound G1 with PIR sensor base | Selectable, up to 42W | 5,460 lm | See product page | 48" x 5.1" x 1.9" | $39.50 |
| EDIPAI Wraparound G3 with sensor base | 15 / 20 / 30 / 40 / 50W | 6,500 lm | See product page | 48" x 10" x 3.2" | $54.25 |
| EDIPAI Wraparound G3 with sensor base and emergency driver | 15 / 20 / 30 / 40 / 50W | 6,500 lm | See product page | 48" x 10" x 3.2" | $117.00 |
All seven run on 120 to 277V, and the EDIPAI G3 with emergency driver is listed for 120 to 347V. Lumens are the top wattage setting, so output drops when you pick a lower setting. Open the spec sheet linked on each product page before you build the fixture schedule, because options such as sensors and CCT are tied to the exact order code.
Five spec sheet lines that separate one wrap from another
1. Selectable wattage and CCT
Selectable fixtures carry several wattage and color temperature settings on one part number, so one box covers a dim storage room and a bright corridor. The Gielight WR has four wattage settings and five CCTs; the JEE J WRAP has three wattages and five CCTs from 3500K to 6500K; both TCP Select Series wraps offer three wattages and 3500K, 4000K or 5000K. Set the switches before the lens goes on, and record the settings if the job needs lighting power paperwork. More on how the switches work: selectable wattage and CCT explained, and for picking the color, the 3000K vs 4000K vs 5000K guide.
2. Sensor base or sensor ready
A sensor turns the wrap off when the hall or room is empty, which many energy codes require in spaces such as storage rooms. The two EDIPAI wraps ship with a sensor base (the G1 listing names a PIR sensor base). The Gielight WR sheet shows a sensor port under a dust cover, where a certified sensor twists into place. The JEE sheet lists a microwave motion sensor as optional, mounted on a sensor base, and the motion sensor version is a separate order code on the sheet. The TCP Select Series Wrap SW3 sheet calls out a large wiring compartment with knockouts for lighting controls. For the difference between PIR and microwave detection, see occupancy sensors: PIR, microwave and dual tech, or browse LED fixtures with occupancy sensors.
3. Emergency driver
In an egress path, the wrap may need to stay on when the power drops. The EDIPAI G3 with emergency driver carries the driver in the fixture, so you do not need a separate emergency unit on that run. The product page and spec sheet we have do not state the emergency runtime, so ask us for the runtime before you finalize the egress plan, and confirm the egress lighting layout with the designer or inspector. The emergency battery backup guide covers how backup fixtures are tested, and the battery backup collection has other options.
4. Dimming
The Gielight, JEE and both TCP sheets list 0 to 10V dimming: the TCP sheets call it standard, and the JEE sheet says it works with a standard 0 to 10V dimmer. The EDIPAI sheets list 0 to 10V as an option, and the two EDIPAI G3 product pages list 0 to 10V dimming, so confirm it on the product page for the exact model. That is low voltage dimming with its own pair of wires, not a phase cut wall dimmer. See 0 to 10V dimming explained before you order wall controls.
5. Size, housing and mounting
Most 4ft wraps are about 5 inches wide and 2 inches deep, close to the fluorescent wraps they replace. The EDIPAI G3 is the exception at 10 inches wide and 3.2 inches deep, so check the old footprint and any paint line before you swap. The TCP sheets list steel housings and surface or suspended mounting, with pendant added on the SW3. The JEE sheet lists ceiling or J box installation with hanging optional. The Gielight sheet lists surface mount as standard, with J box and suspension mounting shown in the instructions.
Damp rooms. Both TCP Select Series sheets list a cULus damp location rating. The EDIPAI G3 sheet lists an IP22 rating for indoor use. For a wash down area or anything wet, a wrap is the wrong fixture; look at vapor tight LED fixtures instead, and see wet vs damp location ratings.
Picking a wrap for the job
- Lowest posted price in the table, for back rooms and closets: the Gielight WR 4ft, with four wattages, five CCTs and a sensor port if you add a sensor later.
- Classrooms and offices that want a dimmable, low profile wrap: the JEE J WRAP or the TCP Modern Wrap SW4.
- Corridors that need the lights off when empty: the EDIPAI G1 with PIR sensor base or the EDIPAI G3 with sensor base.
- Egress paths that need backup light: the EDIPAI G3 with sensor base and emergency driver.
- Not sure how many you need: check the target light level in foot candle requirements by space type, then compare lumens per fixture.
Check each product page and spec sheet for that fixture's UL, ETL and DLC listings. If you plan to apply for a utility incentive, check the DLC listing for the exact model and options; programs vary, check with your utility. Every line we carry has a minimum 5 year manufacturer warranty.
Before you order
- Measure the old fixture and the mounting points, especially if you are looking at the 10 inch wide EDIPAI G3.
- Confirm the voltage on the circuit: 120 to 277V for most wraps, 120 to 347V where the product page lists it.
- Decide on sensors now, because sensor bases and sensor versions are separate order codes.
- Pick one CCT for the building and set it the same on all fixtures in a run.
- Check the dimming wiring if you plan to run 0 to 10V wall controls.
Need help with the numbers? See how to read an LED spec sheet.
Common questions
What size is a 4ft LED wraparound light?
Most 4ft wraps we list are about 47 to 48 inches long, 5 inches wide and 2 inches deep, close to a two lamp fluorescent wrap. The EDIPAI G3 is wider at 48 x 10 x 3.2 inches. Check the spec sheet dimensions against the old fixture.
Can I replace a fluorescent wraparound with an LED wraparound?
Yes. Remove the old fixture and mount the LED wrap to the ceiling or junction box per the manufacturer instructions. The LED wrap has its own driver, so there are no tubes or ballast to keep.
Are LED wraparound lights dimmable?
The Gielight, JEE and TCP Select Series sheets list 0 to 10V dimming, and EDIPAI lists 0 to 10V as an option. 0 to 10V needs a compatible low voltage dimmer, not a standard phase cut wall dimmer.
Do LED wraparound lights come with an occupancy sensor?
Some do. The EDIPAI G1 and G3 wraps we list ship with a sensor base, the Gielight WR has a sensor port for a certified sensor, and the JEE sheet lists a motion sensor version under a separate order code.
How is shipping handled?
We ship to all 50 states by parcel or LTL freight, direct from the manufacturer's warehouse. Submit your order for a freight quote with the delivery address, and nothing is charged until you approve the final total.
Shop the wraparound collection or all 4ft LED fixtures, or send your fixture list for a job quote. Questions? Contact us or call (845) 681 2684.
Ready to price the job?
Build your order and submit it for a freight quote. We ship from the manufacturer's warehouse to all 50 states, and nothing is charged until you approve the total.
Request a freight quote